Titebond Concrete Repair is a flexible, acrylic latex formula specifically designed for repairing and sealing cracks in steps, patios, driveways, sidewalks and mortar joints. Its excellent adhesion and flexibility will not peel, chip, crack or pull away from repaired areas. It provides an air-tight, weather-resistant seal that helps prevent water and ice damage.

Features & Benefits

  • IDEAL FOR: Sealing cracks in steps, patios, driveways, sidewalks and mortar joints.
  • SEALS: Concrete, stucco, metal, masonry, wood and most common building materials.
  • Fills and seals cracks in concrete & masonry
  • Durable - Resists oil, gas, grease & salt
  • Textured formula blends with surface
  • Extrudes easily, excellent adhesion
  • Weather-resistant seal
  • Mildew resistant
  • Paintable
  • UV-resistant


  • ASTM C834 Type OP Grade -18°C

Application Guidelines

  • Application Temperature: Above 40°F (4°C)
  • Service Temperature Range: -25°F to 180°F (-31°C to 82°C)
  • Method of Application: Cartridge/caulking gun
  • Working Time: Approximately 10-15 minutes for a 1/4" bead
  • Application Directions: 1. Surfaces must be clean and free of any material that may prevent adequate adhesion. Properly designed joint not to exceed 1/2" in width. 2. Cut tip at 45° angle to desired bead width and place in cartridge gun. 3. Force sealant into clean joint. If necessary, smooth bead immediately. 4. Do not allow foot or vehicular traffic on repaired area until it is completely dry. It is the sole responsibility of the user to thoroughly test any proposed use with all substrates to determine project suitability. NOTE: Two layers of Concrete Repair, 1/4” to 1/2” thick that are allowed to dry thoroughly between applications, are better than one heavy layer.
  • Cleanup: Clean uncured material with water. After curing, excess sealant must be cut or scraped away.
  • Coverage:
    Container 1/8” Bead 1/4" Bead 3/8" Bead 1/2" Bead
    10.1 oz. Cartridge 123 ft. 31 ft. 14 ft. 8 ft.

Physical Properties

  • Type: Acrylic latex
  • Calculated VOC: <50 g/L (<1.5%)
  • Color: Gray
  • Solids: 83%
  • Flashpoint: Solvent free/Not applicable
  • Viscosity: 550,000 cps
  • Freeze / Thaw Stability: Stable
  • Storage Life: 24 months in a dry location at or below 75°F


Not designed for continuous submersion or use below the waterline. Air, sealant and surface temperature should be above 40°F. Do not apply if rain is expected within 12 hours. Cure time is dependent upon ambient conditions including temperature and humidity. The sealant should be dry to the touch and ready to paint in 2-4 hours. Allow to cure for 24 hours before direct contact with water. For best results, store in a dry location at or below 75°F.

Product SKUs

Part NumberUPCCase UPCSizeWeightUnits Per PackagePackages Per PalletColor
317103708303171310037083031710Currently Unavailable - 10.1 Oz. Cartridge15.0012108

Warranty Statement

Liability is limited to product replacement only.

Important Notice: Our recommendations, if any, for the use of this product are based on tests believed to be reliable. Since the use of this product is beyond the control of the manufacturer, no guarantee or warranty, expressed or implied, is made as to such use or effects incidental to such use, handling or possession or the results to be obtained, whether in accordance with the directions or claimed so to be. The manufacturer expressly disclaims responsibility therefore. Furthermore, nothing contained herein shall be construed as a recommendation to use any product in conflict with existing laws and/or patents covering any material or use.

2020 Bruck Street, Columbus, Ohio 43207
CUSTOMER SERVICE 1-800-669-4583
TECH SERVICE 1-800-347-4583

Franklin International